Pedders Shock Absorber Service Pty Ltd

PO Box 247

NOBLE PARK VIC 3174

ATTENTION: Mr David Schneiders

 

Dear Mr Schneiders

The application for a Identification Plate Approval, your reference number RG2COLCA2, our reference number 48965, lodged for Pedders Shock Absorber Service Pty Ltd, has been approved.

Your approval number is 48965 and the approval documents are attached.

Yours sincerely

Umesh Shamdasani

Associate Administrator of Vehicle Standards

30 November 2017

 

 

 

 

 

 

 

GPO Box 594 Canberra ACT 2601 Telephone: (02) 6274 7111 Facsimile: (02) 6274 7477 http://rvcs.infrastructure.gov.au/

 

Department of Infrastructure and Regional Development

MOTOR VEHICLE STANDARDS ACT 1989

Section 10A.(1) Approval

Approval No.: 48965

Issue date: 30 November 2017

The Associate Administrator of Vehicle Standards (the Associate Administrator) approves the affixing, by the Licensee named and described in Schedule 1 (the Licensee) to a vehicle of the kind described in Schedule 2 which conforms to the design as specified in the evidence items listed in Schedule 4 (the specified vehicle) which the Licensee has certified complies with the Australian Design Rules specified in Schedule 4, of an Identification Plate of the colour specified in Schedule 3, that conforms with the Administrator’s circular 0-3-2, and which contains the information shown in Schedule 2 (with the typical VIN replaced with the relevant VIN).

In this approval, a reference to an Australian Design Rule is a reference to a rule cited in the National Standard determinations, made under section 7 of the Motor Vehicle Standards Act, together with that rule’s distinguishing number.

The licensee must pay a fee to the Commonwealth, in accordance with Regulation 60 and Items 1 and 2 of Schedule 2 of the Motor Vehicle Standards Regulations, for the placement of an identification plate on each new vehicle supplied to the market in Australia in accordance with the approval. The administrative arrangements for the payment of fees are set out in Administrator’s Circular 0-3-2. Where a condition exists in Schedule 5 of the approval for the licensee to obtain plates through the Authorised Plate Contractor, this fee is collected as part of that process.

This approval is subject to the following conditions.

  1. The Licensee shall not affix the Identification Plate to a vehicle that is not a specified vehicle.
  2. The Licensee must not place Identification Plates on vehicles which do not comply with all of the Australian Design Rules specified in Schedule 4.
  3. The Licensee shall not without the prior approval of the Administrator affix the Identification Plate to a vehicle that is in any way different from the vehicle described in the final form of the application for this Approval. The application includes reports and other documents relating to the application.
  4. The Licensee shall by detailed quality control and test ensure continuing compliance with such of the Australian Design Rules specified in Schedule 4.
  5. The Licensee shall maintain records of detailed quality control and test documentation.
  6. The Licensee shall supply upon request, to the satisfaction of the Administrator, any additional information for the purpose of demonstrating compliance with such of the Australian Design Rules specified in Schedule 4.
  7. The Licensee shall not affix the Identification Plate to a vehicle on or after the implementation date for a new Australian Design Rule applicable to the specified vehicle.
  8. The Licensee shall not affix the Identification Plate to a vehicle on or after the Expiry date specified in Schedule 3 (if any).
  9. The Identification Plate shall be affixed to the vehicle to which it relates in the position specified as Plate Location in Schedule 3.
  10. On cessation of marketing the specified vehicle in Australia, the Licensee shall notify the Administrator of the date of manufacture and VIN of the last specified vehicle supplied to the market in Australia.
  11. The Licensee shall also comply with the additional conditions specified in Schedule 5.

Approval No.: 48965 Issue Date: 30 November 2017

Schedule 1

Pedders Shock Absorber Service Pty Ltd

6 Bridge Road

KEYSBOROUGH

VIC 3173

 

Schedule 2

Make : Pedders Holden

Model : RG2 Colorado GVM PLUS

Category : NA

Manufactured by : Pedders Shock Absorber Service Pty Ltd

Typical VIN : MMU148DK0HH600398

Seating Capacity : 2; 4; 5

GVM : 3.3 tonne TO 3.45 tonne

 

Schedule 3

Expiry date : Life of Model

Plate location : LOWER LEFT HAND B PILLAR (10 M 19)

Plate colour : SILVER

Umesh Shamdasani

Associate Administrator of Vehicle Standards

30 November 2017

Please note: If you do not comply with a condition specified in this Approval the Administrator may, after giving you notice, revoke the Approval.

Approval No.: 48965 Issue Date: 30 November 2017

Schedule 4

ADR Document Reference from evidence item

01/00 RGCOL0100

02/01 RGCOL0201

03/03 RGCOL0303

04/05 RGCOL0405

05/05 RGCOL0505

06/00 RGCOL0600

08/01 RGCOL0801

10/02 (also satisfying 10/01) RG2COL1002

10/02 RG2COL1002

11/00 RGCOL01100

13/00 RG2COL1300-2

14/02 RGCOL1402

18/03 RGCOL1803

23/02 (also satisfying 23/01) RGCOL2302

23/02 RGCOL2302

25/02 RGCOL2502

30/01 RGCOL3001

35/05 (also satisfying 31/03) RG2SE3505-5

35/05 (also satisfying 31/03) RG2SE3505-6

35/05 (also satisfying 31/04) RG2SE3505-5

35/05 (also satisfying 31/04) RG2SE3505-6

31/35SF RGSF3505-1

31/35SF RGSF3505-2

31/35SF RGSF3505-3

31/35SF RGSF3505-4

35/05 RG2SE3505-5

35/05 RG2SE3505-6

42/04 RG2COLSE4204

43/04 RG24304-1

44/02 RGCOL4402

46/00 RGCOL4600

47/00 RGCOL4700

48/00 RGCOL4800

49/00 RGCOL4900

50/00 RGCOL5000

51/00 RGCOL5100

61/02 RGCOL6102

62/02 RGCOL6202

69/00 RGCOL6900

72/00 RG2COL72001

76/00 RGCOL7600

79/04 RGCOL7904

81/02 RGCOL8102

83/00 RGCOL8300

Approval No.: 48965 Issue Date: 30 November 2017

Schedule 5

 

1. This approval is for second-stage-of-manufacture (make) PEDDERS HOLDEN (model) RG2 COLORADO GVM PLUS based on first-stage Approval No. 47708 HOLDEN RG issued on 03 May 2016.

2. The Licensee must obtain all second-stage Identification Plates from the Administrator, as per the contract approved by the Administrator for the supply of Identification Plates, currently with:

Niddrie Nameplates Pty Ltd

P.O. Box 106

Niddrie

VIC 3042

Phone: (03) 9335 2977

Facsimile: (03) 9335 4357